Concrete Batch Plants and Associated Equipment

Concrete batch plants and associated equipment including mixers and cement/ash storage silos emit air contaminants including particulate matter and toxic air contaminants. Stationary concrete batch plants and portable plants that do not meet the regulatory definition of portable require a permit to operate. For information on registering a portable concrete batch plant, please see the District's registration page.

Concrete batch plants typically consist of equipment to store and transfer aggregate and cement to the plant, all transfer screws, conveyers, hoppers and mixers included in the plant and equipment used to transfer the mixture of aggregate and cement to trucks for transport or other method of loadout. Cement storage silos and mixers not associated with a batch plant also require separate permits. Particulate (dust) emissions generated from this equipment are typically controlled by enclosing the process, using wet material or adding water or venting any emissions generated through a dust collector or other fabric filter.

The information on this page will assist in the completion and submittal of an application for each concrete batch plant. Each section of the page contains important information needed to submit an application.

Application forms tell us about your operation and allow us to permit your process. Accurate and complete information decreases processing time and helps avoid additional charges for unnecessary revisions. Please carefully review and complete the following forms. Also listed below are required attachments that need to be submitted with the application. You may contact the District with any questions.

General Application: Word PDF

Concrete Batch Plant Supplemental Form Word PDF

Toxics Form: Word PDF

Required Attachments:

  • Plot Plan including stack and/or other release point location(s) and nearby building dimensions
  • Equipment brochures/process flow diagram
  • Bag-house/filter specifications and control efficiency (if applicable)
  • BACT analysis (if applicable)

The general and equipment specific application forms along with required attachments must be submitted with each application packet.

The correct fee must be submitted with your application in order for it to be accepted. For this type of equipment, fees are determined based on the time and materials required to conduct the review, so a fee estimate must be obtained from the District prior to submittal. Please note that application fees are estimated and the final fee may be more or less than this amount based on time and materials spent processing the application. The District maintains work records for this purpose.

Before submitting an application, contact the District (see Assistance tab) to obtain an application fee estimate for application submittal. Please note that an additional fee may also apply depending on the method of payment. A breakdown of how the application fee(s) are determined can be seen here. Additional information can be found in District Rule 40.

How to Pay

These fees may be paid by check payable to "Air Pollution Control District" or by credit card (Visa, MasterCard, Discover, and American Express).

If you choose to email or fax your application and intend on paying with a credit card, ensure that you have obtained your fee estimate and have it in hand, and then after submitting the application, you must contact the District over the phone at (858)586-2600 to provide payment information.

Please note that credit card payments are assessed a transaction fee of 2.19% that is charged by the credit card provider.

Citizen Access
Select equipment type applications can now be submitted online.

Fax: (858) 586-2601

SDAPCD
Permit Processing
10124 Old Grove Rd
San Diego, CA 92131-1649

The District will act on complete applications as soon as possible but at most within 180 days. The engineer assigned to your application will review it and contact you within 30 days of receipt to confirm that it is complete or request additional information. Typically permits are issued in about 60 days. More complex processes will take longer. Common reasons that applications may take longer than 60 days to evaluate include: the project is a complex project specifically at a major source, if the project requires a mandatory public notice period due to being installed within 1000 feet of a school or triggering the requirement for a air quality impact analysis (AQIA), if they do not initially pass a health risk assessment (HRA) or AQIA, if BACT is not proposed or complete BACT analysis is not submitted or for major sources if actual emission data is not included.

Ensuring your application is complete is the best way to reduce processing time. Complete emissions data is the most important factor in minimizing application processing time and iterative information requests. If you have any questions about what information is required, please contact the District using the information on the Assistance tab.

Sign up for Citizen Access to get up to date information on the status of your application.

Learn more about the permitting process and what to expect.

Best Available Control Technology

If a piece of equipment or a process emits more than 10 pounds per day of particulate matter (PM10), oxides of nitrogen (NOx), volatile organic compounds (VOC) or oxides of sulfur (SOx), the application must include a best available control technology (BACT) analysis. For concrete batch plants, this requirement is typically triggered by PM10. Please note that the 10 pounds per day threshold is based on emissions for the entire process line including fugitive emissions from haul roads and storage piles.

If you have questions or need assistance reference the contact information on the assistance tab. Please review District Rules 20.1 and 20.2.

Toxics

District Rule 1200 applies to any new, relocated, or modified emission unit which may increase emissions of one or more toxic air contaminant(s). The proposed project must comply with Rule 1200. Proposed equipment may require toxics best available control technology (TBACT) depending on the project. Please review District Rule 1200 for further details.

Trade Secret

District rules address how information that is submitted to the District is managed. District Regulation IX contains District Rules 176 and 177. Please refer directly to these rules when submitting trade secret information. However, be aware that you will need to submit:

  1. You must indicate on the general application form that your submittal includes trade secret information to ensure that it is not inadvertently made publicly available.
  2. A letter disclosing the proprietary information. Ideally, this information should be separated from your application and clearly identifiable. This can be submitted electronically, and can be a separate submittal from the main application package.
  3. A letter for the  public record explaining why the information needs to be held as trade secret or is otherwise exempt from disclosure.

Applications submitted with incomplete material composition data due to failure to include proprietary information can significantly delay permit applications. In an effort to expedite the permit application process it is recommended that you contact the manufacturer or vendor of any proprietary materials that are used in the process and prepare the required letters as part of your application submittal.

AB3205

In 1989, the California state legislature passed a law, AB 3205, designed to protect schoolchildren from hazardous air contaminants. The law, as currently written, requires the District to notify parents of schoolchildren, neighboring businesses and residents of all new or modified equipment that emits any hazardous air contaminant into the air which will be installed within 1,000 feet of a school site. The law also requires the District to consider any comments before authorizing construction. Please review your proposed location. If a school property boundary is located within 1,000 feet of the proposed emissions point, the AB3205 process will be initiated. This process requires a 30 day public comment period and the overall process will delay projects by at least six weeks.

NESHAP/NSPS/ATCM

This Equipment not subject to any of these rules.

District Rules

Several District rules may apply to your equipment. General rules that may apply to concrete batch plants include Rules 505152, and 54.

There are no equipment specific rules for this equipment. A complete listing of the District's rules can be found here.

Calculation Procedures and Additional Resources

Equipment Calculation Procedures - This page contains procedures to be used for calculating emissions from this equipment that should be submitted with each application.

Use of these calculation procedures will aid in minimizing application review time and costs.  The correct emission factors should be selected from the list based on equipment. If available, manufacturer provided equipment specific emission data or source test results should be utilized before using default emission factors. Sources of all emission data used must be included as attachments to the application.

AP-42 - An alternative compilation of emission factors and calculation procedures prepared by the EPA that may be utilized by the District in some situations for some equipment types.

Call Duty Engineer
(858) 586-2600

District Small Business Assistance Program Coordinator
(858) 586-2650